IEC 60745-2-3 pdf download

IEC 60745-2-3 pdf download.Hand-held motor-operated electric tools – Safety
3 Terms and definitions
This clause of Part 1 is applicable, except as follows: 3.1 01 blotter thin piece of an easily compressible material, between the abrasive product and flange 3.1 02 disk-type sander tool, constructed like a grinder, intended for sanding 3.1 02.1 angle disk-type sander tool with the rotating spindle at a right angle to the motor shaft, intended for lateral sanding 3.1 02.2 straight disk-type sander tool with the rotating spindle in-line with the motor shaft, intended for peripheral or lateral sanding 3.1 02.3 vertical disk-type sander tool with the rotating spindle in-line with the motor shaft, intended for lateral sanding 3.1 03 flange collar, disc or plate between or against which wheels are mounted 3.1 03.1 unrecessed flange flange fixed to the machine spindle having an unrecessed flat surface against which a threaded hole abrasive product is screwed, e.g. a cup wheel, a cone or a plug 3.1 03.2 recessed flange flange fixed to the machine spindle having a recessed flat surface 3.1 03.3 flange outside diameter outside diameter of the contact surface of a flange 3.1 03.4 backing flange contacts and provides support to the back side of the wheel and is located on the spindle between wheel and tool 3.1 03.5 locking flange supports the front side of the wheel and secures and clamps the wheel to the spindle and the backing flange 3.1 04 grinder tool driving a rotating spindle on which a bonded abrasive product is mounted 3.1 04.1 angle grinder tool with the rotating spindle at a right angle to the motor shaft, intended for peripheral and lateral grinding 3.1 04.2 straight grinder tool with the rotating spindle in-line with the motor shaft, either equipped with an abrasive wheel intended for peripheral grinding, or but not equipped with a collet or chuck intended for use with mounted wheels, points or burrs 3.1 04.3 vertical grinder tool with the rotating spindle in-line with the motor shaft, intended for peripheral and lateral grinding 3.1 05 mounted wheels various shapes and sizes that may be either organic or inorganic bonded abrasives and are mounted on a mandrel or threaded onto a mandrel threaded wheels organic or inorganic bonded abrasives of various types provided with a threaded insert for direct mounting to the grinder spindle 3.1 06 polisher tool equipped with a rotating disk or pad intended for polishing 3.1 06.1 angle polisher tool with the rotating spindle at a right angle to the motor shaft, intended for peripheral and lateral polishing 3.1 06.2 straight polisher tool with the rotating spindle in-line with the motor shaft, intended for peripheral polishing 3.1 06.3 vertical polisher tool with the rotating spindle in-line with the motor shaft, intended for lateral polishing 3.1 07 rated capacity maximum diameter of the rotating accessory to be fitted on the tool as recommended by the manufacturer’s instruction 3.1 08 rated speed maximum attainable speed, with any recommended accessory installed, at rated voltage or at the upper limit of the rated voltage range designated by the manufacturer rated speed maximum attainable speed as designated by the manufacturer, with any recommended accessory installed, at rated voltage or at the upper limit of the rated voltage range
8.1 2.1 .1 01 Safety instructions for all operations
Safety Warnings Common for Grinding, Sanding, Wire Brushing, Polishing or Abrasive Cutting-Off Operations: NOTE In the above heading, those operations not applicable may be omitted. a) This power tool is intended to function as a grinder, sander, wire brush, polisher or cut-off tool. Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. NOTE List only those operations that are recommended. b) Operations such as grinding, sanding, wire brushing, polishing or cutting-off are not recommended to be performed with this power tool. Operations for which the power tool was not designed may create a hazard and cause personal injury. NOTE List only those operations that were not included in the first warning. If all listed operations are recommended, then this warning may be omitted but all subsequent warnings must be given without an exclusion. Operations such as grinding, sanding, wire brushing, polishing or cutting-off are not recommended to be performed with this power tool. Operations for which the power tool was not designed may create a hazard and cause personal injury.