ASME B18.31.3:2009 pdf download Threaded Rods (Inch Series)
1INTRODUCTION1.1 Scope
This Standard covers the complete general and dimen-sional data for inch series threaded rods recognized asAmerican National Standard. Included are diameters#4 through 4 in. UNC,UNF,8UN, and ACME in bothright- and left-handed threads.
At this time, there are no ISO standards for inchthreaded rods.
The inclusion of dimensional data in this Standard isnot intended to imply that all of the products describedherein are stock production sizes. Consumers shouldconsult with suppliers concerning lists of stock produc-tion sizes.
1.2 Dimensions
All dimensions in this Standard are in inches, unlessotherwise specified.
1.3 Terminology
All terms used in this Standard are defined inASME B18.12.
1.4Referenced Standards
Unless otherwise specified, the standards referencedshall be the most recent at the time of order placement.ASME B1.1,Unified Inch Screw Threads (UN andUNR Thread Form)
ASME B1.3M,Screw Thread Gaging Systems forDimensional Acceptability -Inch and Metric ScrewThreads (UN,UNR,UNJ,M, and MJ)
ASME B1.5,Acme Screw Threads
ASME B18.12，Glossary of Terms for MechanicalFasteners
ASME B18.18.2,Inspection and Quality Assurance forHigh-Volume Machine Assembly Fasteners
ASME B18.24,Part Identifying Number (PIN) CodeSystem Standard for B18 Fastener Products
Publisher: The American Society of MechanicalEngineers (ASME),Three Park Avenue,New York,NY 10016; Order Department: 22 Law Drive,Box 2300,Fairfield, NJ 07007-2300 (www.asme.org)
ASTM A 193/A 193M,Standard Specification forAlloy-Steel and Stainless Steel Bolting Materials forHigh Temperature or High Pressure Service and OtherSpecial Purpose Applications
ASTM A 307 ,Carbon Steel Bolts and Studs, 60 000 PSITensile Strength
ASTM A 380, Standard Practice for Cleaning, Descaling,and Passivation of Stainless Steel Parts, Equipment,and Systems
ASTM F 468,Standard Specification for NonferrousBolts, Hex Cap Screws, and Studs for General Use
ASTM F 593, Standard Specification for Stainless SteelBolts,Hex Cap Screws, and Studs
ASTM F 788/F 788M, Standard Specification for SurfaceDiscontinuities of Bolts,Screws, and Studs,Inch andMetric Series
ASTM F 1470,Standard Practice for Fastener Samplingfor Specified Mechanical Properties and PerformanceInspection
ASTM F 1554,Anchor Bolts,Steel,36,55,and 105-ksiYield Strength
ASTM F 1941,Electrodeposited Coatings on ThreadedFasteners (Unified Inch Screw Threads (UN/UNR))
Publisher: American Societv for Testiasa(uuNR))(ASTM International)， 100 Barr Harbor Drive,
P.o. Box C700，West Conshohocken，PA 19428(www.astm.org)
2GENERAL DATA2.1 Length
Threaded rods are commonly produced in, but notlimited to, 3-ft,6-ft,10-ft, and 12-it lengths.The lengthof the threaded rod shall be measured, overall, from endto end. The length tolerance on all threaded rods innominal lengths of 6 ft and longer shall be 王7/in. and士/ in. for nominal lengths less than 6 ft. See Fig.1.
2.2 Threads
Unified threads shall conform to the requirements ofASME B1.1.For UNC and UNF threads,Class 1A willbe furnished unless otherwise specified. Plated threadsshall conform to ASME B1.1,Class 3A high limit (basic)and the low limit requirement of the before-coated orplated thread class. Class 2A threads shall be used on8 UN threads and at the manufacturer’s option for otherseries, and for sizes where 1A is not applicable.
ACME threads shall meet the requirements of ASMEB1.5,Class 2G, unless otherwise specified.
2.3 Thread Acceptance Gaging
Unless otherwise specified by the purchaser, gagingfor screw thread dimensional acceptability shall be inaccordance with Gaging System 21 as specified in ASMEB1.3M.
ASME B18.31.3:2009 pdf download
